2002/12 (A·C) 284-9724-00 Installation/Wire Connection Guide I Fixed Mount (TOYOTA, NISSAN and other ISO/DIN equipped vehicles) I I This unit is designed for fixed installation in the dashboard. If the vehicle is equipped with a factory-installed radio, install the source unit with the parts and screws marked (*). (Figure 6) If the vehicle is not equipped with a factory-installed radio, obtain an installation kit to install the source unit in the following procedure. English * * 1. BEFORE STARTING / 2. Read these instructions carefully. / 1. Secure the mounting brackets to the chassis as shown in Figure 6. Holes are pre-tapped for TOYOTA and NISSAN vehicles; modification, such as drilling new holes, of the mounting brackets may be required for other models. 2. Wire as shown in Section 6. 3. Secure the unit in the dashboard, and then reassemble the dashboard and the center panel. 1. This set is exclusively for use in cars with a negative ground, 12 V power supply. 3. Be sure to disconnect the battery " " terminal before starting. This is to prevent short circuits during installation. (Figure 1) Note 1: In some cases, the center panel may require some modification (trimming, filling, etc.). Note 2: If a hook on the installation bracket interferes with the unit, bend and flatten it with a nipper or a similar tool. Car battery Mounting bracket * (1 pair for the left and right sides) * Figure 1 / English / * Dashboard 2. CAUTIONS ON INSTALLATION / 1. Prepare all articles necessary for installing the source unit before starting. 2. Install the unit within 30° of the horizontal plane. (Figure 2) 3. If you have to do any work on the car body, such as drilling holes, consult your car dealer beforehand. 4. Use the enclosed screws for installation. Using other screws can cause damage. (Figure 3) / *: * * # The parts and screws with this mark are used to install radio or included in the installation kit. #: The screws with this mark are originally attached to the vehicle. # # # Source Unit # 4­Hexagonal screw * (M5 × 8) * Pocket # # # × * × Chassis / Max. 30° / Chassis / Max. 5/16" (8 mm) / Center Panel (Note 1) Note 2 / / Damage Figure 6 / English / Figure 2 / English / Figure 3 / / 3. INSTALLING THE SOURCE UNIT / I Universal Mount 1. Place the universal mounting bracket into the instrument panel, use a screwdriver to bend each stopper of the universal mounting bracket inward, then secure the stopper as shown in Figure 4. 2. Wire as shown in Section 6. 3. Insert the source unit into the universal mounting bracket until it locks. 4. Take care of the top and bottom of the outer escutcheon and mount it so that all the hooks are locked. (Figure 5) 4. REMOVAL OF THE SOURCE UNIT / / I 1. When removing the source unit, disassemble it in the reverse of the order in Section "3. INSTALLING THE SOURCE UNIT". 2. Press the outer escutcheon upward and remove it. (Figure 7) 3. Insert and lock the hook plates. (Figure 8) 4. Pull the hook plates to remove the source unit. / I 2­Hook plate Outer escutcheon Notes: 1) Some car models require special mounting kits for proper installation. Consult your Clarion dealer for details. 2) Fasten the front stopper securely to prevent the source unit from coming loose. English · Console opening dimensions · · 7-3/16" (182 mm) Instrument panel Hole Figure 7 / / Figure 8 / / 5. CAUTIONS ON WIRING / 53 mm 2-1/8" Hole Hexagonal bolt / Stoppers Strap Top * This part is not provided in some models. * * Installation direction Screwdriver 1. Be sure to turn the power off when wiring. 2. Be particularly careful where you route the wires. Keep them well away from the engine, exhaust pipe, etc. Heat may damage the wires. 3. If the fuse should blow, check that the wiring is correct. If it is, replace the fuse with a new one with the same amperage rating as the original one. 4. To replace the fuse, open the lock on the source unit side, remove the old fuse and insert the new one. (Figure 9) * There are various types of fuse cases. Do not let the battery side terminal touch other metal parts. 5. Connect the CeNET extension cable fully and securely until it locks. When the CeNET extension cable is pulled, hold the slide cap part and pull it towards you. * When the CeNET extension cable is extended or branches, use extension cable CCA-520 (8 feets [2.5m]) or CCA-521 (2 feets [0.6m]), or Y-adapter CCA-519 (each of them is sold separately). * Use the CeNET extension cable made by Clarion. * * * * Source Unit Universal mounting bracket * Note: Before attaching the universal mounting bracket, slightly bend the spring toward the inside with your fingers and attach it to the side of car. * Example 1 Bottom Spring Stoppers Fuse Example 2 Fuse case Example 3 Fuse Fuse Outer escutcheon Outer escutcheon side view Fuse case Fuse case Figure 4 / / Figure 5 / / Figure 9 / / English English 6. WIRE CONNECTIONS / I RCA Pin Cable / I · · 7. SAMPLE SYSTEMS / I · · / I Example of the system using an external amplifier. (AUDIO) I I & · Connect to an external amplifier. · To eliminate audio short circuits, do not remove the caps of unused RCA cables. I Example of the system using an internal amplifier. I I 7 1 ¥ Red / / Front Right # : 5.1 ch surround play When using 5.1 ch surround playback, change the speaker settings on the source unit to switch to subwoofer and center speaker. #: #: Gray White / / 2 Front Left 4 2 1 7 ¥ Red / / Rear Right / Rear Left White / Black Red (Right side) / 5 6 3 ! @ TM 4 Amp Amp 8 / Non-fader Right (Subwoofer#) # White (left side) / Purple / Non-fader Left (Center speaker#) # # I Example of the system using an external amplifier. (AUDIO, VISUAL) I I % Red / / AUX INPUT Right £ # I Rear Layout I I Antenna Rear View of the Source Unit Red / / AUX INPUT Left & # 5 $ 6 or White / / 2 1 7 ) ¥ * ( ¡ ! @ CeNET input 16-Pin Connector Extension Lead (attached to the source unit) 3 8 Note: Use a CeNET extension cable that is less than 20 m in length. (including the Y-adapter CCA-519.) + Gray / + Front Right /+ Brown wire (Phone mute lead) 7 /Connect to cellular phone mute lead. 9 - Gray/Black / - 4 + White / + Front Left /+ - White/Black / - /Yellow wire (Memory back-up lead) 5 6 0 ! @ + Purple / + Rear Right /+ Fuse (15A) Connect directly to battery. English - Purple/Black / - /- Rear Left + Green / + /+ Yellow wire (Bus power lead) Connect directly to battery. Fuse (3A) - Green/Black / - /- 4-Speaker system Red wire (Power lead) Accessory + 12 V + + or Blue/White wire (Amplifier turn-on lead) 2-Speaker system Connect to remote turn-on lead of amplifier. 1 2 3 4 5 6 7 8 9 0 ! @ # $ % ¥ & * ( ) ¡ TM £ Right + Gray / + /+ Source Unit CeNET extension cable DTS/Dolby digital unit Y-adapter (sold separately) MD changer CD Changer RCA Extension Cable (sold separately) 4-Channel Power Amplifier 2-Channel Power Amplifier Subwoofers Front Speakers Rear Speakers Expanded TV Tuner Module Monitor/Tuner Connection Cable Video Monitor External Unit SIRIUS tuner or Expanded DAB tuner module DVD Changer Optical connector cable Center speaker (with amplifier) Subwoofer (with amplifier) RCA cable (packed with center speaker) RCA cable (sold separately) 1 2 3 4 5 6 7 8 9 0 ! @ # $ % ¥ & * ( ) ¡ TM £ 1 2 3 4 5 6 7 8 9 0 ! @ # $ % ¥ & * ( ) ¡ TM £ - Gray/Black / + White / + Left /+ /- Black wire (Ground lead) Connect to vehicle chassis ground. English 8. GENERAL CAUTIONS / /Orange wire (Illumination lead) Connect it to the car power supply terminal for illumination. / - White/Black / + Purple / + /+ 1. Do not open the case. There are no user serviceable parts inside. If you drop anything into the unit during installation, consult your dealer or an authorized CLARION service center. 2. Use a soft, dry cloth to clean the case. Never use hard cloth, thinner, benzen, alcohol, etc. For tough dirt, apply a little cold or warm water to a soft cloth and wipe off the dirt gentry. - Purple/Black / + Green / + Not used. Insulate each wire. /+ /- Blue wire (Auto antenna lead) - Green/Black / /Connect it to the car power supply terminal for the antenna. IMPORTANT: Improper installation may cause damage to your unit or car. If you do not have the appropriate experience, consult a qualified installer. Cutting chassis wire leads voids the warranty. Clarion Co., Ltd. ...