2006/12 284-1002-00 Installation/Wire Connection Guide PRECAUTION Remove the stopper following the procedures below when this source unit is installed without the universal mounting bracket. 1. Remove the screw from the source unit (Figure 5). 2. Remove the stopper from the source unit (Figure 6). 3. Install the remove screw to the source unit (Figure 7). Securely attach the screw. 1. 2. 3. 1. 2. 3. English 1. BEFORE STARTING / 1. This set is exclusively for use in cars with a negative ground, 12 V power supply. 2. Read these instructions carefully. 3. Be sure to disconnect the battery "-" terminal before starting. This is to prevent short circuits during installation. (Figure 1) 1. 2. 3. / 12V 1. 2. 1 1 3. "-" Car battery Note: Store the removed stopper in a safe place together with the Instruction Manual. 12V Example 1/ 1/ 1 1 Stopper/ 2 Source Unit/ 3 Screwdriver/ 4 Screw/ / / / / 3 4 Figure 1 / 1/ 1 1 English 2. CAUTIONS ON INSTALLATION / 1. Prepare all articles necessary for installing the source unit before starting. 2. Install the unit within 30° of the horizontal plane. (Figure 2) 3. If you have to do any work on the car body, such as drilling holes, consult your car dealer beforehand. 4. Use the enclosed screws for installation. Using other screws can cause damage. (Figure 3) 1. 2. 3. 4. / 1. 30° 2 3 4. 3 2. 3. 30° 2 2 Figure 5 / 5/ 5 Figure 6 / 6/ 6 Figure 7 / 7/ 7 Fixed Mount (Using the bracket originally equipped in vehicle) This unit is designed for fixed installation in the dashboard. If the vehicle is equipped with a factory-installed radio, install the source unit with the parts and screws marked (). (Figure 8) If the vehicle is not equipped with a factory-installed radio, obtain an installation kit to install the source unit in the following procedure. 1. Secure the mounting brackets to the chassis as shown in Figure 8. When the source unit is installed without the universal mounting bracket, holes exist; modification, such as drilling new holes, of the mounting brackets may be required for other models. 2. Wire as shown in Installation (Section 6). 8 1. 2. 3. 8 8 1. 6 2. 3. 6 8 Chassis / / Chassis / / Damage / / 3. Secure the unit in the dashboard, and then reassemble the dashboard and the center panel. Mounting bracket * (1 pair for the left and right sides) Dashboard Max. 30° / 30° / 30° Max. 8 mm / 8 mm / 8 mm * * Figure 2 / 2/ 2 Figure 3 / 3/ 3 Source Unit English 3. INSTALLING THE SOURCE UNIT / Universal Mount 1. Place the universal mounting bracket into the instrument panel, use a screwdriver to bend each stopper of the universal mounting bracket inward, then secure the stopper as shown in Figure 4. 2. Wire as shown in Section 6. 3. Insert the source unit into the universal mounting bracket until it locks. 4. Take care of the top and bottom of the outer escutcheon and mount it so that all the hooks are locked. 4­Hexagonal screw * (M5 × 8) 4 * (M5 × 8) * M5 × 8 4 / 1. 4 2. 3. 4. 6 2. 3. 4. 6 Note 2 / Center Panel (Note 1) 1 1 2/ 2 Pocket 1. 4 Figure 8 / 8/ 8 : The parts and SCREW with this mark are used to install radio or included in the installation kit. : The screws with this mark are originally attached to the vehicle. Note 1: In some cases, the center panel may require some modification (trimming, filling, etc.). Note 2: If a hook on the installation bracket interferes with the unit, bend and flatten it with a nipper or a similar tool. 1 2 1 2 Notes: 1) Some car models require special mounting kits for proper installation. Consult your Clarion dealer for details. 2) Fasten the front stopper securely to prevent the source unit from coming loose. 1) 2) Clarion 1) 2) English 4. REMOVAL OF THE SOURCE UNIT / 1. When removing the source unit, disassemble it in the reverse of the order in Section "3. INSTALLING THE SOURCE UNIT". 2. Remove the Detachable Control Panel (DCP). For instructions on removing the DCP, refer to the owner's manual. 1. 2. 3. 4. 5. 10 3 DCP DCP 9 3. Press the outer escutcheon upward and remove it. (Figure 9) 4. Insert and lock the hook plates. (Figure 10) 5. Pull the hook plates to remove the source unit. / 3 1. 2. 3. 4. 5. 10 DCP DCP 9 "3 " · Console opening dimensions · · 7-3/16" (182 mm) Stoppers Hole 53 mm 2-1/8" Instrument panel Hole Outer escutcheon Hexagonal bolt 2­Hook plate 2 Strap Figure 9 / 9/ 9 Figure 10 / 10 / 10 Top * This part is not provided in some models. * * English 5. CAUTIONS ON WIRING / 1. Be sure to turn the power off when wiring. 1. 2. 3. 2. Be particularly careful where you route the wires. Keep them well away from the engine, exhaust pipe, etc. Heat may damage the wires. 3. If the fuse should blow, check that the wiring is correct. If it is, replace the fuse with a new one with the same amperage rating as the original one. (Figure 11) / 1. 2. 11 Screwdriver Source Unit Installation direction Universal mounting bracket 3. 11 Spring Note: There are various types of fuse holder. Do not let the battery side touch other metal parts. 4. CeNET CeNET 521 0.6 Clarion 5. 15 30 Y CeNET CCA-519 15 CeNET CCA-520 2.5 CCA4. CeNET CeNET CeNET 2.5m Clarion Fuse Stoppers Bottom Outer escutcheon Outer escutcheon side view Note: Before attaching the universal mounting bracket, slightly bend the spring toward the inside with your fingers and attach it to the side of car. 4. Connect the CeNET extension cable fully and securely until it locks. When the CeNET extension cable is pulled, hold the slide cap part and pull it towards you. When the CeNET extension cable is extended or branches, use extension cable CCA-520 (2.5m) or CCA-521 (0.6m), or Y-adapter CCA-519 (each of them is sold separately). Use the CeNET extension cable made by Clarion. 5. When the main power supply fuse in the car is 15 A or less, purchase an automotive cable that can withstand 15 A and supply this unit with power directly from the battery to ensure that the unit will operate normally. Note that a fuse must be installed at a distance no longer than 30 cm from the cable battery terminal to prevent accidents. CCA-520 CCA-521 0.6m CeNET 15A 30 cm 15A Y CCA-519 5. Fuse case Figure 4 / 4/ 4 Figure 11 / 11 / 11 English English 6. WIRE CONNECTIONS / To external amplifier / 1 2 3 4 RCA 7. SYSTEM EXAMPLE / / Example of iPod BB and Bluetooth BB connection CAUTION: Please make sure when connecting external power amplifier, that you properly, to the car chassis, ground the amplifier. If this is not done, severe damage to the source unit may happen. * To eliminate audio short circuits, do not remove the caps of unused RCA cables. Example of the system using an external amplifier (Audio Visual) * * 0 ! 6 iPod connector cable / / 5 1 iPod/ iPod mini EA-1276 2 1 6 # Antenna @ 3 7 ( & or / / $ CeNET input CeNET CeNET * This system has an external input jack on the front panel, so you can listen to your telephone calls or music from external devices on your car speaker. Amp Amp 4 5 % ¥ 8 9 Note: Use a CeNET extension cable that is less than 20 m in length. (including the Y-adapter CCA-519.) 20 m CeNET 20 m 16-Pin Connector Extension Lead (attached to the source unit) 16 16 +Gray / + Front Right -Gray/Black / //+ CCA-519 CCA-519 CeNET This source unit can control a total of 2 changers except 2 DVD changers exist in the system. 2 DVD 2 2 DVD 2 Brown wire (Phone mute lead) English Note: Some units do not have connecting leads or jacks. (Refer to .) +White / + Front Left /+ Connect to cellular phone mute lead. -White/Black / - /Yellow wire (Memory back-up lead) +Purple / + Rear Right /+ Connect directly to battery. -Purple/Black / - /- +Green / + Rear Left /+ Fuse (15A) 15A 15A -Green/Black / - /- Yellow wire (Bus power lead) Connect directly to battery. English No. 1 2 3 4 5 Description FRONT RIGHT Gray (Red) FRONT LEFT Gray (White) REAR RIGHT/SUB WOOFER Black (Red) REAR LEFT/SUB WOOFER Black (White) OEM STEERING WHEEL REMOTE CONTROL INPUT (Black) 4-Speaker system 4 4 Fuse (3A) 3A 3A Red wire (Power lead) 1 2 3 4 5 6 7 8 9 0 ! @ # $ % ¥ & * ( Source unit CeNET extension cable Y-adapter (sold separately) CD changer DVD changer RCA extension cable (sold separately) 4-Channel power amplifier Front speakers Rear speakers Monitor TV tuner module 5.1ch surround decoder 5.1ch surround decoder control unit Optical connector cable Center speaker (with amplifier) Subwoofer (with amplifier) External unit Aux Bluetooth BB (BLT370) Stereo mini-plug cable (sold separately) 1 2 3 4 5 6 7 8 9 0 ! @ # $ % ¥ & * ( CeNET Y CD DVD RCA 4 TV 5.1 5.1 1 2 3 4 5 6 7 8 9 0 ! @ # $ % ¥ & * ( CeNET Y CD DVD RCA 4 TV 5.1 5.1 or Accessory+12 V +12 V +12 V Blue/White wire (Amplifier turn-on lead) 2-Speaker system 2 2 Connect to remote turn-on lead of amplifier. +Gray / + Right Black wire (Ground lead) -Gray/Black / /) /+ 1 2 3 4 5 English 8. GENERAL CAUTIONS / 1. Do not open the case. There are no user serviceable parts inside. If you drop anything into the unit during installation, consult your dealer or an authorized CLARION service center. 2. Use a soft, dry cloth to clean the case. Never use hard cloth, thinner, benzen, alcohol, etc. For tough dirt, apply a little cold or warm water to a soft cloth and wipe off the dirt gentry. / CLARION CLARION +White / + Left /+ Connect to vehicle chassis ground. -White/Black / - /Orange/White wire (Illumination lead) / +Purple / + /+ -Purple/Black / - /- Connect it to the car power supply terminal for illumination. 1 2 3 4 5 IMPORTANT: Improper installation may cause damage to your unit or car. If you do not have the appropriate experience, consult a qualified installer. Cutting chassis wire leads voids the warranty. +Green / + Not used. Insulate each wire. /+ Blue wire (Auto antenna lead) Green/Black / - /- Connect it to the car power supply terminal for the antenna. Clarion Co., Ltd. ...